Schneider Electric

Schneider Electric ATV930U22Y6 Atv930Ip00 2,2Kw 500V-690V Variable Spe

SKU:

ATV930U22Y6

UPC:

3.60648E+12

MPN:

Condition:

New

Minimum Switching Current:

relay output R1, R2, R3 5 mA 24 V DC

Sampling Duration:

2 ms +/- 0.5 ms DI1...DI8) - discrete input || 5 ms +/- 1 ms DI7, DI8) - pulse input || 1 ms +/- 1 ms AI1, AI2, AI3) - analog input || 5 ms +/- 1 ms AQ1, AQ2) - analog output

Analogue Output Type:

software-configurable voltage AQ1, AQ2 0...10 V DC 470 Ohm 10 bits || software-configurable current AQ1, AQ2 0...20 mA 500 Ohm 10 bits

Braking To Standstill:

by DC injection

Motor Slip Compensation:

automatic whatever the load || adjustable || can be suppressed || not available in permanent magnet motor law

Nominal Switching Frequency:

4 kHz

Relative Humidity:

5-95 % without condensation IEC 60068-2-3

Local Signalling:

local diagnostic 3 LED mono/dual colour) || presence of voltage 1 LED red) || embedded communication status 3 LED dual colour) || communication module status 4 LED dual colour)

Overvoltage Category:

III

Eu Rohs Directive:

Pro-active compliance (Product out of EU RoHS legal scope)

Ambient Air Temperature For Operation:

-15-50 °C without derating) || 50-60 °C with derating factor)

Weee:

The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins.

Apparent Power:

4.3 kVA 690 V normal duty) || 3.1 kVA 690 V heavy duty)

Degree Of Protection:

UL type 1

Maximum Acceleration Under Vibrational Stress (During Operation):

10 m/s² at 13...200 Hz

Connector Type:

2 RJ45 || 1 RJ45

Operating Altitude:

<= 3280.84 ft (1000 m) without derating || 1000...4800 m with current derating 1 % per 100 m

Communication Port Protocol:

EtherNet/IP || Modbus serial || Modbus TCP

Prospective Line Isc:

70 kA

Circularity Profile:

ENVEOLI1704001EN

Analogue Input Number:

3

Shock Resistance:

15 gn 11 ms IEC 60068-2-27

Product Specific Application:

process for industrial

Range Of Product:

Altivar Process ATV900

Environmental Disclosure:

ENVPEP1704001EN

Protection Type:

thermal protection motor || safe torque off motor || motor phase break motor || thermal protection drive || safe torque off drive || overheating drive || overcurrent between output phases and earth drive || overload of output voltage drive || short-c

Asynchronous Motor Control Profile:

variable torque standard || optimized torque mode || constant torque standard

Reach Regulation:

Reference contains Substances of Very High Concern above the threshold

Device Application:

Industrial Application

Base Load Current At Low Overload:

3.1 A

With Safety Function Safe Brake Management (Sbc/Sbt):

TRUE

Phase:

3 phase

With Safety Function Safe Torque Off (Sto):

TRUE

Relative Symmetric Network Frequency Tolerance:

0.05

Environmental Characteristic:

chemical pollution resistance class 3C3 IEC 60721-3-3 || dust pollution resistance class 3S3 IEC 60721-3-3

Emc Filter:

integrated || with EMC plate option

Mercury Free:

Yes

Electromagnetic Compatibility:

electrostatic discharge immunity test level 3 IEC 61000-4-2 || radiated radio-frequency electromagnetic field immunity test level 3 IEC 61000-4-3 || electrical fast transient/burst immunity test level 4 IEC 61000-4-4 || 1.2/50 µs - 8/20 µs surge im

Accuracy:

+/- 0.6 % AI1, AI2, AI3 for a temperature variation 60 °C analog input || +/- 1 % AQ1, AQ2 for a temperature variation 60 °C analog output

Power Dissipation In W:

forced convection 43 W 500 V 4 kHz || natural convection 73 W 500 V 4 kHz

Input Compatibility:

DI1...DI8 discrete input level 1 PLC IEC 61131-2 || DI7, DI8 pulse input level 1 PLC IEC 65A-68 || STOA, STOB discrete input level 1 PLC IEC 61131-2

Noise Level:

58 dB

Network Frequency:

50-60 Hz

Discrete Input Logic:

positive logic (source) DI1...DI8), < 5 V, > 11 V || negative logic (sink) DI1...DI8), > 16 V, < 10 V || positive logic (source) DI7, DI8), < 0.6 V, > 2.5 V || positive logic (source) STOA, STOB), < 5 V, > 11 V

Sustainable Offer Status:

Green Premium product

Maximum Output Voltage:

690.0 V

With Safety Function Safe Programmable Logic:

FALSE

With Safety Function Safe Direction (Sdi):

FALSE

With Safety Function Safe Operating Stop (Sos):

FALSE

Variant:

standard version || with braking chopper

Maximum Transient Current:

3.72 A 60 s normal duty) || 3.6 A 60 s heavy duty)

Vibration Resistance:

1.5 mm peak to peak 2-13 Hz)IEC 60068-2-6 || 1 gn 13-200 Hz)IEC 60068-2-6

Maximum Output Frequency:

599 Hz

Method Of Access:

slave Modbus TCP

Type Of Polarization:

no impedance Modbus serial

Continuous Output Current:

3.1 A 4 kHz normal duty || 2.4 A 4 kHz heavy duty

Linearity Error:

AI1, AI2, AI3 +/- 0.15 % of maximum value analog input || AQ1, AQ2 +/- 0.2 % analog output

Operating Position:

vertical +/- 10 degree

Assembly Style:

enclosed

Physical Interface:

Ethernet || 2-wire RS 485

China Rohs Regulation:

X

Ambient Air Transport Temperature:

-40-70 °C

Synchronous Motor Control Profile:

permanent magnet motor || synchronous reluctance motor

Transmission Frame:

RTU

4 Quadrant Operation Possible:

TRUE

Standards:

UL 508C || IEC 61800-3 || IEC 61800-5-1 || IEC 61000-3-12 || IEC 60721-3 || IEC 61508 || IEC 13849-1

Analogue Input Type:

AI1, AI2, AI3 software-configurable voltage 0...10 V DC 30 kOhm 12 bits || AI1, AI2, AI3 software-configurable current 0...20 mA/4...20 mA 250 Ohm 12 bits

Exchange Mode:

half duplex, full duplex, autonegotiation Ethernet IP/Modbus TCP

Product Or Component Type:

variable speed drive

Transmission Rate:

10, 100 Mbits || 4.8 kbps || 9600 bit/s || 19200 bit/s

Option Card:

slot A communication module Profibus DP V1 || slot A communication module PROFINET || slot A communication module DeviceNet || slot A communication module EtherCAT || slot A communication module CANopen daisy chain RJ45 || slot A communication module

Width:

246 mm

Data Format:

8 bits, configurable odd, even or no parity Modbus serial

Number Of Addresses:

1-247

Relay Output Type:

configurable relay logic R1 fault relay NO/NC 100000 cycles || configurable relay logic R2 sequence relay NO 1000000 cycles || configurable relay logic R3 sequence relay NO 1000000 cycles

Discrete Input Type:

DI1...DI8 programmable, 24 V DC <= 30 V)3.5 kOhm || DI7, DI8 programmable as pulse input 0-30 kHz, 24 V DC <= 30 V) || STOA, STOB safe torque off, 24 V DC <= 30 V)> 2.2 kOhm

Marking:

CE

California Proposition 65:

WARNING: This product can expose you to chemicals including: Lead and lead compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Rohs Exemption Information:

Yes

Depth:

242 mm

Upgradeability:

Upgraded components available

Data Format:

8 bits, configurable odd, even or no parity

Permitted Relative Humidity (During Operation):

class 3K5 according to EN 60721-3

Line Current:

3.4 A 500 V normal duty) || 2.6 A 500 V heavy duty) || 3.6 A 690 V normal duty) || 2.6 A 690 V heavy duty)

Ip Degree Of Protection:

IP21

Discrete Input Number:

10

Noise Level:

58 dB 86/188/EEC

With Safety Function Safe Stop 1 (Ss1):

TRUE

Discrete Output Number:

2

Number Of Addresses:

1-247 Modbus serial

Transmission Rate:

10/100 Mbit/s Ethernet IP/Modbus TCP || 4.8, 9.6, 19.2, 38.4 kbit/s Modbus serial

Insulation Resistance:

> 1 MOhm 500 V DC for 1 minute to earth

[Us] Rated Supply Voltage:

500...690 V - 15...10 %

Isolation:

between power and control terminals

Height:

420 mm

Mounting Mode:

wall mount

Volume Of Cooling Air:

330 m3/h

Type Of Polarization:

no impedance

Brake Chopper Integrated:

TRUE

Maximum Acceleration Under Shock Impact (During Operation):

150 m/s² at 11 ms

Regulation Loop:

adjustable PID regulator

Supply:

external supply for digital inputs 24 V DC 19-30 V), <1.25 mA overload and short-circuit protection || internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <10 mA overload and short-circuit protection || internal supply for d

Switching Frequency:

2...8 kHz adjustable || 4...8 kHz with derating factor

With Sft Fct Safe Stop 2 (Ss2):

FALSE

Product Certifications:

TÜV || UL || CSA

With Safety Function Safe Position (Sp):

FALSE

Net Weight:

22 kg

Motor Power Kw:

1.5 kW normal duty || 1.1 kW heavy duty

Discrete Output Type:

logic output DQ+ 0-1 kHz <= 30 V DC 100 mA || programmable as pulse output DQ+ 0-30 kHz <= 30 V DC 20 mA || logic output DQ- 0-1 kHz <= 30 V DC 100 mA

Analogue Output Number:

2

With Safety Function Safe Speed Monitor (Ssm):

FALSE

Quantity Per Set:

1

Pollution Degree:

2

Base Load Current At High Overload:

2.4 A

Refresh Time:

relay output R1, R2, R3)5 ms +/- 0.5 ms)

Relay Output Number:

3

Maximum Deflection Under Vibratory Load (During Operation):

1.5 mm at 2...13 Hz

Maximum Switching Current:

relay output R1 resistive, cos phi = 1 3 A 250 V AC || relay output R1 resistive, cos phi = 1 3 A 30 V DC || relay output R1 inductive, cos phi = 0.4 7 ms 2 A 250 V AC || relay output R1 inductive, cos phi = 0.4 7 ms 2 A 30 V DC || relay output R2, R

Discrete Input Logic:

16 preset speeds

Ambient Air Temperature For Storage:

-40-70 °C

Electrical Connection:

control screw terminal 0.5...1.5 mm² AWG 20...AWG 16 || DC bus screw terminal 4...10 mm² AWG 12...AWG 8 || line side screw terminal 4...10 mm² AWG 12...AWG 8 || motor screw terminal 4...10 mm² AWG 12...AWG 8

Environmental Class (During Operation):

class 3C3 according to IEC 60721-3-3 || class 3S3 according to IEC 60721-3-3

Product Destination:

synchronous motors || asynchronous motors

Acceleration And Deceleration Ramps:

S, U or customized || linear adjustable separately from 0.01...9999 s

With Safety Function Safely Limited Position (Slp):

FALSE

With Safety Function Safely Limited Speed (Sls):

TRUE

Brochure:

View

Catalog:

View

Datasheet:

View