Adjustable Mounting Height Stopper Cylinders

The SMC RSG series is a flange-mounted stopper cylinder whose mounting height is set by moving the included flange along the cylinder body, so the stopper can be matched to the conveyor after installation. Automation Distribution carries RSG and RSDG in 40mm and 50mm bore with 20, 25, and 30mm strokes, in round bar, chamfered, roller, and shock absorber lever rod ends.

Pick RSDG when you need auto switch position feedback, then choose the rod end by pallet weight and speed. Jump to the specifications, rod end selection, part number guide, or FAQ.

SMC RSG Specifications

SpecificationRSG / RSDG
Bore size40mm, 50mm
Standard stroke20, 25, 30mm (both bores, all rod ends)
ActionDouble acting (D), double acting with spring loaded (B), single acting spring extend (T)
MountingFlange, height adjusted by repositioning the included flange
PortRc 1/8 (standard), NPT 1/8 (TN), G 1/8 (TF), or built-in One-touch fittings (F) for 6mm tubing on 40mm and 8mm tubing on 50mm
Max operating pressure1.0 MPa (proof pressure 1.5 MPa)
Ambient and fluid temperature-10 to 70°C without auto switch, -10 to 60°C with auto switch (no freezing)
Cushion and lubricationRubber bumper, non-lube
Spring force (single acting)13.7 N extended, 27.5 N compressed (round bar, chamfered, roller)

Choosing the RSG Rod End

Size from pallet weight and conveyor speed using SMC's operating range charts. In SMC's examples, a 30 kg pallet at 15 m/min falls in the range of the RSG40 roller type, and a 60 kg pallet at 15 m/min (friction coefficient 0.1) falls in the range of the RSG40 lever type with lock mechanism.

CodeRod EndUse It When
NoneRound barBasic stop for light loads.
KChamfered (non-rotating rod)The contact face must stay square to the pallet.
RRollerRolling contact against the pallet face.
LLever, non-adjustable shock absorberHeavier pallets with consistent weight and speed.
BLever, adjustable shock absorberPallet energy varies or needs tuning. An adjustment bolt sets the absorber stroke.
CLever, adjustable, with cancel capSome pallets must pass. The cancel cap holds the lever horizontal.
DLever, adjustable, with lock mechanismLight pallets would rebound. The lock holds the lever upright after impact.
ELever, adjustable, with lock and cancel capBoth needs on one stopper.

SMC notes that a lever without a lock can be pushed back against the transfer direction by the shock absorber's return force if less than 10 N of conveyor thrust holds the pallet against it. If the lever must stay upright, choose D or E.

Reading an RSG Part Number

Example: RSDG40-30DC-M9BW

SegmentMeaning
RSDGRSG series with built-in magnet (RSG has no magnet and cannot take an auto switch)
40Bore: 40 or 50mm. A port code follows here if not Rc: TN (NPT), TF (G), F (One-touch fittings)
30Stroke: 20, 25, or 30mm
DAction: D double acting, B double acting with spring loaded, T single acting spring extend
CRod end (see table above)
M9BWAuto switch model, then lead wire length (none 0.5m, M 1m, L 3m, Z 5m) and S for one switch instead of two

Installation and Ordering Notes

  • Setting height: after positioning the flange, tighten the body lock nut, then the two set screws supplied with it.
  • Auto switches: D-A9 and D-M9 switches ship with the cylinder but are not assembled; only the mounting brackets come installed. Specify the mounting bracket symbol when ordering these switch types.
  • Orientation: the piping port ships flush with the pallet contact surface. Keep the pallet contact face parallel to the cylinder so no rotational torque reaches the rod.
  • Single acting models: do not apply pressure to the head side, or air will blow by.
  • Made to order: rod end shape changes (-XA) and special port position (-XC3) are available.

RSG Maintenance Parts

Seal kits are ordered by bore and action: RSG40D-PS and RSG50D-PS (double acting), RSG40B-PS and RSG50B-PS (double acting with spring loaded), RSG40T-PS and RSG50T-PS (single acting). The lever replacement shock absorber for both bores is RB1407-X552, and the grease pack is GR-S-010. Find them in Stopper Cylinder Parts.

RSG Stopper Cylinder FAQ

How do you adjust the mounting height of an SMC RSG stopper cylinder?

The RSG mounts through an included flange that can be positioned along the cylinder body. Set the flange where the stopper meets the pallet at the required height, then tighten the body lock nut followed by its two set screws.

What is the difference between SMC RSG and RSQ stopper cylinders?

RSG has an adjustable mounting height through its flange and comes in 40 and 50mm bore. RSQ (now RSQ-Z) has a fixed mounting height with through-hole or both-ends-tapped mounting and covers 12 to 50mm bore. Choose RSG when the conveyor height is not fixed or must be set during commissioning.

What does the D in RSDG mean?

The D means the cylinder has a built-in magnet so auto switches can detect the stopper position. RSG without the D has no magnet and cannot use auto switches. A part number such as RSDG50-25D is a magnet-equipped cylinder ordered without switches.

Which RSG rod end stops light pallets without rebound?

Choose the lever type with lock mechanism, rod end D, or rod end E for lock and cancel cap. The lock holds the lever upright after the pallet strikes it, so the shock absorber's return force cannot push the pallet back. SMC recommends a lock whenever the lever must remain upright.

Is the SMC RSG series discontinued?

No. The RSG and RSDG are current SMC products. The older RSQ in 16 to 50mm bore was replaced by RSQ-Z in 2018, but that change did not affect the RSG.

Need help selecting an RSG stopper?

Send us the pallet weight, conveyor speed, and any current part number. Automation Distribution, an authorized SMC distributor, will confirm bore, rod end, and auto switch.

Contact Automation Distribution