4 x 16-bit data: 4 x 8-bit control/status (optional)
depth:
67.8 mm / 2.669 inch
depth from upper edge of din rail:
60.6 mm / 2.386 inch
dielectric strength:
510 VAC/775 VDC: per EN 60870-2-1
emc emission of interference:
Per EN 61000-6-3, -4, EN 61131-2, EN 60255-26, marine applications, EN 60870-2-1, EN 61850-3
emc immunity to interference:
Per EN 61000-6-1, -2, EN 61131-2, marine applications, EN 60255-26, EN 60870-2-1, EN 61850-3, IEC 61000-6-5, IEEE 1613, VDEW: 1994
ex guideline:
EN/IEC 60079-0, -7, -11
exposure to pollutants:
Per IEC 60068-2-42 and IEC 60068-2-43
fine stranded conductor:
0.25 2.5 mm / 24 14 AWG
fire load:
1.247 MJ
height:
100 mm / 3.937 inch
housing material:
Polycarbonate: polyamide 6.6
input resistance max:
200
intrinsic safety ex i:
Yes
isolation:
300 VAC system/field
marking:
ATEX/IECEx: II 3 (1) G Ex ec [ia Ga] IIC T4 Gc: II (1) D [Ex ia Da] IIIC: I (M1) [Ex ia Ma] I
measurement error deviation max from the upper range value:
0.001
measurement error reference temperature:
25 C
mounting position:
Horizontal (standing/lying): vertical
mounting type:
DIN-35 rail
note:
The analog output module must only be operated via 24 VDC Ex i XTR power supply (750-606/040-000)!General information (e.g., installation regulations) on explosion protection is available in the WAGO I/O System 750 XTR manuals!
number of analog inputs:
4
number of incoming power jumper contacts:
2
number of outgoing power jumper contacts:
2
operating altitude:
Without temperature derating: 0 2000 m: with temperature derating: 2000 5000 m (0.5 K/100 m): 5000 m (max.)
packaging type:
Box
permissible h2s contaminant concentration at a relative humidity 75:
10 ppm
permissible so2 contaminant concentration at a relative humidity 75:
25 ppm
pollution degree 5:
2 per IEC 61131-2
power consumption 5 v system supply:
45 mA
power consumption field supply module with no external load:
19 mA
power consumption pmax:
2.7 W (at 4 x 21 mA signal current)
power loss pl:
1.5 W (at 4 x 21 mA signal current)
protection type:
IP20
rated surge voltage:
1 kV: Rated surge voltage between intrinsically safe and non-intrinsically safe circuits: 1.5 kV (EN 60079-11)
reactances ex ia i:
Lo = 36 mH: Co = 3.84 F
reactances ex ia iia:
Lo = 25 mH: Co = 2.36 F
reactances ex ia iib:
Lo = 15 mH: Co = 0.71 F
reactances ex ia iic:
Lo = 1.6 mH: Co = 0.082 F
reactances note:
Reactances without accounting for the concurrence of L and C
relative humidity with condensation:
Short-term condensation per Class 3K7/IEC EN 60721-3-3 and E-DIN 40046-721-3 (except for wind-driven precipitation, water and ice formation)
relative humidity without condensation:
0.95
resolution bit:
12 bits
safety relevant data circuit:
Uo = 26.8 V: Io = 92.72 mA: Po = 621.27 mW: Linear characteristic curve
sensor connection:
2 x (3-wire)
shock resistance:
Per IEC 60068-2-27 (15g/11 ms/half-sine/1,000 shocks: 25g/6 ms/1,000 shocks), EN 61373
signal characteristic:
Single-ended
signal type:
Current
signal type current:
0 20 mADC: 4 20 mADC: 3.6 21 mADC
solid conductor:
0.25 2.5 mm / 24 14 AWG
strip length:
8 9 mm / 0.31 0.35 inch
supply voltage field:
24 VDC: (Ex i XTR power supply: UO = max. 26.8 V): via power jumper contacts (power supply via blade contact: transmission via spring contact)
supply voltage sensor:
15 VDC: Transmitter supply UV at 20 mA
supply voltage system:
5 VDC: via data contacts
surrounding air temperature operation:
-40 70 C
surrounding air temperature storage:
-40 85 C
temperature error max of the upper range value:
0.01 %/K
total number of channels module:
4
vibration resistance:
Per IEC 60068-2-6 (acceleration: 5g), EN 60870-2-2, IEC 60721-3-1, -3
